Handpipe

Product Guide

Quick Start Guide

View PDF

User Manual

Filters
The Handpipe-S accepts 9mm x 36mm length filters of paper, cotton, or activated carbon/charcoal variety.

10 Carbon Filters are included with the Handpipe-S. Install one into the Mouthpiece by pressing it down into the cavity. If the filter does not stay in place, push it down into the Mouthpiece a little bit further.

Replace the filter every 3-5 sessions, or as often as desired to keep your hit tasting fresh.

Replacement Carbon Filters for sale on smokeheir.com

Filters are not required to smoke the Handpipe-S, but we prefer them for the benefit of not having particulates come through when inhaling. 

Smoking
Light the Handpipe-S with a standard butane lighter, such as a Bic or Clipper lighter. Use Hemp-wick for a gas-free alternative.

Do not use a butane torch lighter with the Handpipe-S. This refers to any lighter with a continuous jet-flame which is intended for heating the bowl for an extended period. Do not attempt to heat the Handpipe-S bowl to high temperatures for dabbing or smoking concentrates.

Cleaning
All parts of the Handpipe-S EXCEPT the Cap can be machine washed. Disable the steam/heat dry part of the cycle on your machine to reduce further wear on them while cleaning. The Cap’s magnet will become demagnetized if exposed to high heat, so do not boil it or use any other high-heat methods to clean it.

To clean the Handpipe-S by hand, use pipe cleaners dipped in Isopropyl Alcohol to scrub the interior. Rinse with water, and air dry afterwards.

When scrubbing alone won’t do the job, deep clean the Handpipe-S parts by submerging and soaking them in Isopropyl Alcohol for at least one hour. Then scrub with pipe cleaners, rinse with water, and air dry.

Pipe Cleaners for sale on Amazon

Inner Bowl Removal
Use the Smoke Tool as a lever to pry the Inner Bowl free from the Outer Bowl, as needed for cleaning. Reinstall by pressing the Inner Bowl into the Outer Bowl until the top edge sits just below the rim. Straighten the Inner Bowl inside of the Outer Bowl by poking the Smoke Tool through the Inner Bowl’s hole.

Smoke Tool & Lanyard Attachment
Attach the Smoke Tool to the Mouthpiece by pressing it down until the round head nearly makes contact with the Mouthpiece body. Take caution, the Smoke Tool can disconnect when hanging the Handpipe from it’s Lanyard. The harder you press-fit the Smoke Tool into the Mouthpiece, the more securely it will stay attached.

Capping the Bowl
The cap magnetically attaches on top of the bowl. Nudging the cap to the side will provide an edge for your finger to lift it off of the Outer Bowl. Take care not to spill anything you loaded into the bowl before, when uncapping it.

Cap Stand
The Cap can attach to the base of the Bowl. This gives the Handpipe a stable platform to rest on while you load, and keeps the Mouthpiece clean by keeping it off the ground.

FAQ

The Handpipe-S includes a 30-Day Warranty.

30 Day Warranty period begins on the date that the order is delivered. Our warranty applies to defects that render products non-functioning and less than premium quality. Specifically; air tight sealing, fit and finish defects, and non-accidental breakage caused by regular use as described in our User Manual. If we determine at our sole discretion that the claimed defect is covered by our warranty, we will offer a replacement part at no charge. Email [email protected] with a description of the issue, order number, and picture of the issue, to open a warranty claim.

Returns for full refund are accepted within 30 days of your order’s delivery date, as long as the product is returned unused and in like-new condition. To initiate a return request, email [email protected] with a description of any issue and your order, and your order number. We will reply to accept or deny your return request based upon the timing and condition of your order. When a return request is accepted, instructions will be provided for return shipping the item(s). Return shipping costs are borne by the customer. Once the returned item(s) are received in good condition, a refund will be processed. Refund processing time can take 5-7 business days from the date the returned package is received.

Replacement parts are available as inventory permits. Please visit our shop to find a replacement part. If the part you are looking for is not shown, please contact us.